INTERNATIONAL ISO STANDARD 4463-2 First edition 1995-12-15 Measurement methods for building - Setting-out and measurement . Part 2: Measuring stations and targets Methodes de mesurage pour la construction - Piquetage et mesurage - Partie2:Stationsetbalises ISO Reference number ISO 4463-2:1995(E) ISO4463-2:1995(E) Contents Page Scope 1 1 2 Normative references 1 Definitions 3 1 4 General.. 1 Planning.. 5 1 5.1Location.. 1 5.2 Approvals. 2 5.3 Programme.. 2 Functional needs of stations and targets . 2 6.1 Stability and durability. 2 6.2 Protection 2 6.3 Marking... 2 6.4Stationandtargetdescription 2 Maintenance 4 7.1 Visual. 4 7.2 By measurement 4 Annexes Examples of stations and targets. A 5 B Bibliography. 28 ISO1995 Ail rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. International Organization for Standardization Case Postale 56.CH-1211Geneve 20·Switzerland Printed in Switzerland ii @ ISO ISO4463-2:1995(E) Foreword Iso (the:International Organization for Standardization) is a worldwide federation of national standards bodies (IsO member bodies). The work of preparing.International Standards is normally carried out through IsO technical:committees. Each member body interested in a subject for which.a technical committee has been established has the right to be and non-governmental, in liaison with IsO, also take part in the work. IsO collaborates closely with the International Electrotechnical Commission (IEC) on all-matters of electrotechnical standardization. circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting avote. International Standard ISO 4463-2 was prepared by Technical Committee Iso/TC59,Buildingconstruction,SubcommitteeSC4,Dimensionaltoler ancesandmeasurement. This first edition of ISO 4463-2, together with ISO 4463-1 and iSO 4463-3, cancels-and replacesIsO4463:1979,whichhasbeentechnicallyrevised. IsO'4463 consists of the following parts,under the general title Measure- mentmethods for building-Setting-out and measurement. Part 1:Planningand organization,measuringprocedures,acceptance criteria Part2:Measuringstationsandtargets Part3:Check-listsfortheprocurement of surveysandmeasurement services Annexes A and B of this part of ISO4463 are for information only @ISO INTERNATIONALSTANDARD ISO4463-2:1995(E) Measurement methods for building --- Setting-out and measurement Part 2: Measuring stations and targets Scope 1 3Definitions This part of IsO 4463 deals with the progressive For the purposes of this part of Iso 4463, the defi- stages of establishing and marking measuring stations nitions given in ISO 1803 and ISO 4463-1apply. and targets on building sites. The aspects covered are planning, functional needs and maintenance. 4 General This part of ISO 4463 applies to measuring'stations and targets in all types of building construction. Stations and targets are the basis of all setting-out and Examples of different stations and targets and lo- measuring procedures. It is important that the lo- cation plans are given in annex A. cations of stations and targets are properly planned and constructed to meet their functional requirements throughout the building process. The requirements in- clude the need for stability, accessibility and clear 2 Normative references lines of sight throughout their useful life whereverpossible. The following standards contain provisions which through reference in this text, constitute provisions of The type, quality and permanence of stations and tar this part of ISO 4463. At the time of publication, the gets depend on the particular project requirements in editions indicated were valid. All standards are subject relation to the various categories of setting-out and to revision, and parties to agreements